PLUMBING FOR BEGINNERS: WHAT YOU NEED FOR INSTALLING A BATHTUB

Plumbing for Beginners: What You Need for Installing a Bathtub

Plumbing for Beginners: What You Need for Installing a Bathtub

Blog Article

Schedule A Service Call

Here down the page you can locate a bunch of helpful data on the subject of Installing A Bathtub.


How to Install a Bathtub Yourself
Setting up a bath tub isn't specifically rocket science, however it does require strong plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bathtub with a new one is additionally a moderately difficult task. If the old tub is conveniently easily accessible, the job can relocate immediately; if you have to open a wall surface to remove the old tub and also position the brand-new tub, the job is much harder. In either instance, the job is within a residence handyman's skills, although you will require an assistant to move out the old bathtub and embeded in the brand-new one. Make sure you have certified on your own for the work and are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed job, it is far better to think about utilizing one before you begin. Opportunities are you might require a professional plumber to make tube links.
This write-up will certainly help you mount a brand-new tub in your washroom if you have currently gotten a brand-new bathtub and do not require to alter the plan of your previous water system pipelines.
Your tools as well as material checklist should consist of the following:
  • New Bathtub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Planning for the Installation


    Firstly, the supporting structure provided with the bath should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to make certain that if the faucet features a plastic washer, it is fitted between the bath as well as the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets unit to avoid strain on the bath tub.
    Fit the adaptable tap adapters to the bottom of the two taps using 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
    Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently be ready to be fitted in its last placement.

    Removing Old Taps


    If you require to replace old taps with new ones as a part of your installation, then the first thing you ought to do is detach the supply of water. After doing so, turn on the taps to drain any type of water staying in the system. The procedure of eliminating the existing taps can be rather problematic because of the restricted gain access to that is typically the situation.
    Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. As soon as the faucets have been eliminated, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
    Before carrying on to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.

    Installing the Tub


    Utilizing the two wooden boards under its feet, place the bathtub in the required setting. The wood boards are helpful in equally spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four tiny points.
    The next goal is to make sure that the bathtub is leveled all round. This can be achieved by checking the level and also changing the feet on the bathtub until the level reviews level.
    To install faucets, fit all-time low of the furthest versatile tap adapter to the proper supply pipe by making a compression sign up with; then do the same for the various other tap.
    Activate the water system and inspect all joints and brand-new pipework for leakages as well as tighten them if necessary. Fill the tub as well as also inspect the overflow outlet as well as the regular outlet for leakages.
    Finally, take care of the bathroom paneling as described in the producer's user's manual. Tiling and also securing around the tub needs to wait until the bathtub has been utilized at least when as this will settle it into its final setting.

    Suitable New Touches


    If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end supplies a connection to the existing supply pipes.
    If you need to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
    Next, position the faucet in the mounting opening in the bath/basin making sure that the washers are in area between the faucet as well as the sink. Protect the tap in position with the producer provided backnut. When the tap is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous kind must be attached to the tap finishes first, tightening just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.

    Tiling Around the Bath tub


    In the location where the bathroom satisfies the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the fitting can move enough to crack a rigid seal, creating the water to permeate the wall between the bath and also the tiling, resulting in complications with moisture and also feasible leaks to the ceiling below.
    You can pick from a selection of coloured sealants to blend in your components and installations. They are offered in tubes and also cartridges, and also are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill up the tub with water prior to securing, to allow for the movement experienced when the tub is in usage. The sealer can split fairly early if you do not take into account this motion prior to sealing.
    Conversely, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly readily available on the market. It is suggested to fit the ceramic tiles using water-resistant or waterproof adhesive and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    I ran across that review about How to Install a Bathtub while surfing the internet. Enjoyed reading our blog? Please share it. Help somebody else discover it. Bless you for your time. Don't hesitate to check up our blog back soon.


    Book Today

    Report this page